Other Instruments

2-channel RF power meter for peak and average power with support for continuous, pulse and statistical modes, as well as synchronised two-channel analysis.

Programmable 1- and 3-phase AC sources with output power up to 9 kVA, 0–500 V voltage, harmonic simulation and test functions in accordance with IEC 61000-4-11.

Broadband mixer for up- and down-conversion 5–14 GHz with integrated programmable LO, IF 5–6000 MHz, low phase noise, USB/Ethernet control and compact aluminium housing.

RF signal generator 20–14,000 MHz, output –40 to +15 dBm, 0.25/0.5 dB steps, improved harmonic filtering and Ethernet from Rev 10 (2025).

Low-phase-noise microwave signal generator for RF and microwave applications, covering 0.1–40 GHz, for test, development and automated measurement environments.

Low harmonic distortion RF signal generator for test and measurement, covering 25–6000 MHz and offering calibrated output power as well as local and remote control.

24–6000 MHz RF signal, −22 to +15 dBm output, standalone with OLED display, sweep, SCPI, USB control and TCXO reference.

Two-line V-network for measuring interference voltage on single-phase EUTs, complies with CISPR 16-1-2 and EN 55016-1-2 for measuring conducted emissions.

EM coupling clamp for immunity testing in accordance with IEC/EN 61000-4-6, frequency range 10 kHz–1 GHz, designed for unshielded cables up to 20 mm in diameter.

EM coupling clamp for immunity testing in accordance with IEC/EN 61000-4-6, 10 kHz–1 GHz, for unshielded cables up to 35 mm where a CDN is not suitable.

Switching/disconnection network for immunity testing of conducted RF disturbances per IEC/EN 61000-4-6, with models for unshielded and shielded power and data lines.

Test and pulse generator for insulation and impulse withstand testing of electricity meters, generating a standardised 0.1/2000 µs waveform in accordance with FNN guidelines.

Capacitance coupling clamp for burst testing of data and I/O lines in accordance with IEC/EN 61000-4-4, designed for capacitive coupling during immunity testing.

DC LISN kit with two 5 µH/100 A LISNs, LISN Mate for CM/DM separation, frequency range 9 kHz–110 MHz and complete cable set for EMC measurements in DC systems.

High-current Bias-Tee for RF measurement, designed for analysing saturation and bias voltage effects in inductors and EMC filters with simultaneous DC and RF loading.

CDNE for emission measurement of lighting equipment in accordance with CISPR 15, as an alternative to OATS, 30–300 MHz, for EUTs without a PE connection.

CDNE for emission measurement of lighting equipment in accordance with CISPR 15, as an alternative to OATS, 30–300 MHz, for EUTs with PE, neutral and line connections.

Comb generator for verification of EMC measurement setups, with selectable comb frequencies and an internally reference-characterised radiated spectrum.

Comb generator for verifying antennas, preamplifiers and spectrum analyzers, with fixed comb frequencies and characterised radiated spectrum up to 6 GHz.

General-purpose comb generator for laboratory use with selectable fundamental frequencies and flat comb spectrum up to 1 GHz, for EMC setups, cables and filter measurements.

Symmetrical RF choke for attenuating common-mode currents in impedance measurements, with low insertion loss and a wide frequency range up to 1 GHz.

Differential amplifier with flat response from DC to 250 MHz, 1:50 attenuation and 50 Ω output, intended for CS101 test setups and general measurement.

DC-coupled driver amplifier with 20 dB gain for DC–40 MHz, intended for CS101 testing and amplification of tracking generator signals.

Broadband RF driver amplifier for laboratory use, designed to amplify low-power RF sources or drive power amplifier stages across wide frequency bands.

Broadband RF driver amplifier for laboratory use, designed for amplifying low-power RF sources or driving power amplifier stages across wide frequency bands.

ESD target for verifying ESD simulators in accordance with IEC 61000-4-2, with current-sensing probes and a frequency range from DC up to 4 GHz.

High dynamic range amplifier for EMC measurement, designed as a low-noise preamplifier for spectrum analyzers, receivers and active loop antennas.

Injection transformer for stability measurement of control loops, with galvanic isolation between signal source and DUT, intended for low-frequency RF tests.

Injection transformer for stability measurement of control loops, with galvanic isolation between signal source and DUT, intended for low-frequency measurements.

Injection transformer for CS101 immunity testing with galvanic isolation and high-pass filtering in the frequency range 150 kHz–50 MHz.

Two-way LISN in accordance with ECSS-E-ST-20-07C for EMC measurement of satellites and spacecraft, with 0.7 µH impedance and for use with RF current probes.

Two-way LISN in accordance with ECSS-E-ST-20-07C for EMC measurement of small satellites and spacecraft, with 1 µH impedance and for use with RF current probes.

Universal 5 µH LISN for measuring line-induced interference, configurable for multiple EMC standards and intended for AC and DC-powered equipment with defined impedance.

LISN with 5 µH inductance and 50 A capacity for DC-powered devices, 150 kHz–110 MHz measurement range, in accordance with CISPR 16-1-2 and related standards.

LISN for single-phase AC and DC measurements in accordance with CISPR 16-1-2, 9 kHz–30 MHz, 250 V/8 A, with separate BNC outputs for line and neutral, and switchable PE.

LISN for single-phase AC measurements per CISPR 16-1-2, 9 kHz–30 MHz, 250 V/8 A, with line selector, switchable limiter/attenuator/high-pass filter and PE switch.

Single-channel LISN 50 Ω // 50 µH for measuring conducted emissions in accordance with CISPR 16-1-2, intended for AC and DC-powered equipment with defined impedance.

LISN for single-phase AC and DC measurements in accordance with CISPR 16-1-2, 9 kHz–30 MHz, 250 V/16 A, with separate BNC outputs for line and neutral, and switchable PE.

LISN for single-phase AC measurements per CISPR 16-1-2, 9 kHz–30 MHz, 250 V/16 A, with line selector, switchable limiter/attenuator/high-pass filter and PE switch.

Line Impedance Stabilisation Network for measuring line-borne disturbances in accordance with CISPR 16-1-2, for single-phase and three-phase equipment with separate RF outputs.

Line Impedance Stabilisation Network for measuring line-borne disturbances in accordance with CISPR 16-1-2, for single-phase and three-phase equipment with separate RF outputs.

LISN for measuring conducted emissions on DC power supplies in accordance with CISPR 16-1-2 and CISPR 11, for high DC voltages up to 1000 V.

LISN accessory that separates common-mode and differential-mode components when measuring conducted emissions.

DC-coupled low-noise amplifier with 40 dB gain for DC–110 MHz, intended for low-level signals to measuring receivers and spectrum analyzers.

Preamplifier for passive loop antennas with 43 dB gain for 9 kHz–30 MHz, designed to increase dynamic range during low-frequency EMC measurements.

Linear broadband RF power amplifier for test and measurement applications, designed for general laboratory use with stable gain over a wide frequency range.

Modulated broadband RF power amplifier for immunity tests performed with BCI probes in accordance with ISO 11452-4, intended for CW, AM and PM signals.

Modulated RF power amplifier for immunity testing in accordance with IEC/EN 61000-4-6, designed for operation of CDNs and BCI probes with CW, AM and PM signals.

Modulated broadband RF driver amplifier for immunity testing, designed for CW, AM and PM signals as well as the operation of EMC probes and TEM cells.

Modulated broadband RF driver amplifier for immunity testing, designed for CW, AM and PM signals as well as the operation of near-field probes and TEM cells.

Modulated broadband RF power amplifier for immunity testing, designed for driving CDNs, BCI probes, near-field probes and TEM cells with CW, AM and PM signals.

Modulated broadband power amplifier for RF immunity testing, designed for CW, AM and PM signals, as well as for operating near-field probes and TEM cells.

Modulated RF power amplifier for immunity testing in accordance with IEC/EN 61000-4-6, designed for operation of CDNs and BCI probes with CW, AM and PM signals.

Modulated broadband driver amplifier for immunity testing, designed to drive near-field probes and TEM cells in the 1–3 GHz frequency range with CW, AM and PM signals.

5 µH LISN for EMC pre-testing of DC-powered devices, designed for measuring conducted noise in accordance with CISPR 25 via a measurement output to an analyzer.

Passive receiving loop for MIL-STD-461G RE101 measurement of low-frequency magnetic field emissions in the frequency range 30 Hz–100 kHz.

Passive field monitoring loop for calibration and monitoring during MIL-STD-461G RE101 and RS101 tests in the frequency range 30 Hz–100 kHz.

Radiating loop antenna for generating low-frequency magnetic fields during MIL-STD-461G RS101 immunity tests in the frequency range 30 Hz–100 kHz.

Broadband amplifier for EMC measurement, intended for use between a near-field probe and a spectrum analyzer to increase the dynamic range during RF analysis.

Broadband amplifier for EMC measurement, intended for use between a near-field probe and a spectrum analyzer to increase the dynamic range during RF analysis.