TekBox

DC LISN kit with two 5 µH/100 A LISNs, LISN Mate for CM/DM separation, frequency range 9 kHz–110 MHz and complete cable set for EMC measurements in DC systems.

50 Ω load with N-connector (male), 25 W power, frequency range DC – 3 GHz, VSWR < 1.2.

N-male/N-female for laboratory and test applications, DC–3 GHz frequency range, 100 W power rating and 3 dB attenuation.

N-male/N-female for laboratory and test applications, DC–3 GHz frequency range, 50 W power rating and 3 dB attenuation.

N-male/N-female for laboratory and test applications, DC–3 GHz frequency range, 25 W power rating and 3 dB attenuation.

N-male/N-female for laboratory and test applications, DC–3 GHz frequency range, 10 W power rating and 3 dB attenuation.

Up to 250 MHz. Snap-on RF current monitoring probe for EMC pre-compliance testing.

Up to 250 MHz. Snap-on RF current monitoring probe for EMC pre-compliance testing.

Up to 200 MHz. Snap-on RF current monitoring probe for EMC pre-compliance measurement.

Radiating comb generator with a base frequency of 25 MHz, comb spectrum 30 MHz–6 GHz and internal antenna, battery-powered 9 V.

100 Hz–80 MHz 3 dB bandwidth and −6 dBΩ transimpedance, characterised 1 Hz–100 MHz, 15 mm aperture, N-female and up to 3 A RMS.

20 Hz–70 MHz 3 dB bandwidth and −12 dBΩ transimpedance, characterised 1 Hz–100 MHz, 15 mm aperture, N-female and up to 8 A RMS.

0.5 Hz–30 MHz 3 dB bandwidth and −26 dBΩ transimpedance, characterised 0.1 Hz–100 MHz, 15 mm aperture, N-female and up to 55 A RMS.

2 Hz–40 MHz 3 dB bandwidth and −20 dBΩ transimpedance, characterised 0.1 Hz–100 MHz, 15 mm aperture, N-female and up to 40 A RMS.

OSLT calibration kit DC–6 GHz with Open, Short, Load and Through for VNAs with 3.5 mm/SMA male connectors.

OSLT calibration kit DC–6 GHz with Open, Short, Load and Through for VNAs with 3.5 mm/SMA female connectors.

OSLT calibration kit DC–6 GHz with Open, Short, Load and Through for VNAs with N-male connectors.

OSLT calibration kit DC–6 GHz with Open, Short, Load and Through for VNAs with N-female connectors.

Mounting panel for ESD targets in accordance with IEC 61000-4-2 Edition 3, 120 × 60 cm aluminium, target position 100 cm above ground and support frame 120 × 160 × 50 cm.

Fibreglass stand with a maximum height of 172 cm, folded height of 100 cm, 16 kg load capacity and dual 1/4"-3/8" thread for flexible antenna mounting.

Beech wood stand with max height 205 cm, folded height 100 cm, 15 kg load capacity and integrated spirit level for stable mounting in test and laboratory environments.

Beech wood stand with a height of 800–1800 mm, three sections, integrated spirit level and 8 kg load capacity for stable mounting of antennas in a laboratory environment.

Compact tripod with ABS pistol grip for quick and precise positioning, designed for table and field work, and compatible with TBMA1 and TBMA4.

Carbon fibre tripod with max height 1490 mm, folded height 370 mm, load capacity 6 kg and four sections for stable mounting of antennas and lightweight equipment.

Injection transformer for CS101 immunity testing with galvanic isolation and high-pass filtering in the frequency range 150 kHz–50 MHz.

Large loop antenna with three orthogonal loops for EMC measurement of magnetic field emissions, 9 kHz–30 MHz, developed in accordance with CISPR 16-1-4 and CISPR 15.

Active monopole antenna for EMC pre-compliance measurement of radio interference, 9 kHz–30 MHz in accordance with CISPR 16, for low-frequency emission measurements.

Biconical EMC measurement antenna for pre-compliance testing and field strength generation, 30 MHz–3 GHz, passive broadband design with dipole-like radiation pattern.

For IEC 61000-4-6 Annex D2. 150 kHz–230 MHz, 300 V AC / 600 V DC, 36 A, 150 Ω common-mode impedance and 9.5 dB voltage attenuation.

Snap-on RF current monitoring probe for EMC pre-compliance measurement, 10 Hz–500 MHz, with high saturation resistance and stable transimpedance at high DC currents.

Radiating loop antenna for generating low-frequency magnetic fields during MIL-STD-461G RS101 immunity tests in the frequency range 30 Hz–100 kHz.

Passive field monitoring loop for calibration and monitoring during MIL-STD-461G RE101 and RS101 tests in the frequency range 30 Hz–100 kHz.

Passive receiving loop for MIL-STD-461G RE101 measurement of low-frequency magnetic field emissions in the frequency range 30 Hz–100 kHz.

Symmetrical RF choke for attenuating common-mode currents in impedance measurements, with low insertion loss and a wide frequency range up to 1 GHz.

Symmetrical 50 Ω high-pass filter with 3 dB bandwidth 135 kHz–100 MHz, 250 V rated voltage, 10 W input power and N-male/N-female connectors.

Symmetrical 50 Ω high-pass filter with 3 dB bandwidth 135 kHz–1 GHz, 250 V rated voltage, 10 W input power and N-male/N-female connectors.

Symmetrical 50 Ω high-pass filter with 3 dB bandwidth 110 kHz–3 GHz, max 10 W input power and N-male/N-female connectors for RF input protection during emission measurements.

Balanced 50 Ω high-pass filter with 3 dB bandwidth 9 kHz–1 GHz, max 10 W input power and N-male/N-female connectors for RF input protection during emission measurements.

Differential amplifier with flat response from DC to 250 MHz, 1:50 attenuation and 50 Ω output, intended for CS101 test setups and general measurement.

DC-coupled driver amplifier with 20 dB gain for DC–40 MHz, intended for CS101 testing and amplification of tracking generator signals.

Preamplifier for passive loop antennas with 43 dB gain for 9 kHz–30 MHz, designed to increase dynamic range during low-frequency EMC measurements.

DC-coupled low-noise amplifier with 40 dB gain for DC–110 MHz, intended for low-level signals to measuring receivers and spectrum analyzers.

LISN for single-phase AC measurements per CISPR 16-1-2, 9 kHz–30 MHz, 250 V/16 A, with line selector, switchable limiter/attenuator/high-pass filter and PE switch.

LISN for single-phase AC measurements per CISPR 16-1-2, 9 kHz–30 MHz, 250 V/8 A, with line selector, switchable limiter/attenuator/high-pass filter and PE switch.

LISN for single-phase AC and DC measurements in accordance with CISPR 16-1-2, 9 kHz–30 MHz, 250 V/16 A, with separate BNC outputs for line and neutral, and switchable PE.

LISN for single-phase AC and DC measurements in accordance with CISPR 16-1-2, 9 kHz–30 MHz, 250 V/8 A, with separate BNC outputs for line and neutral, and switchable PE.

2-port measurement 1 Hz–6 GHz with DC-coupled VSWR bridges, four channels and integrated spectrum, oscilloscope and Bode analysis.

Measures conducted emissions 1 Hz–110 MHz with CISPR-16-compliant detectors, STFFT measurement, low noise level and support for EMCView.

LISN accessory that separates common-mode and differential-mode components when measuring conducted emissions.

External 10 µF capacitor for TBL05100-1 LISN, intended for 50/60 Hz applications.

10 µF capacitor module for TBL0550-1, designed for a 250 V source at 50/60/400 Hz.

10 µF capacitor module for TBL0550-1, designed for a 250 V source at 50/60 Hz.

Two-way LISN in accordance with ECSS-E-ST-20-07C for EMC measurement of satellites and spacecraft, with 0.7 µH impedance and for use with RF current probes.

LISN for measuring conducted emissions on DC power supplies in accordance with CISPR 16-1-2 and CISPR 11, for high DC voltages up to 1000 V.

General-purpose comb generator for laboratory use with selectable fundamental frequencies and flat comb spectrum up to 1 GHz, for EMC setups, cables and filter measurements.

Modulated broadband driver amplifier for immunity testing, designed to drive near-field probes and TEM cells in the 1–3 GHz frequency range with CW, AM and PM signals.

Current injection probe for conducted immunity in accordance with IEC/EN 61000-4-6 with snap-on function, 150 kHz–230 MHz operating range and injection levels up to 30 V.

Two-way LISN in accordance with ECSS-E-ST-20-07C for EMC measurement of small satellites and spacecraft, with 1 µH impedance and for use with RF current probes.

CDNE for emission measurement of lighting equipment in accordance with CISPR 15, as an alternative to OATS, 30–300 MHz, for EUTs with PE, neutral and line connections.

CDNE for emission measurement of lighting equipment in accordance with CISPR 15, as an alternative to OATS, 30–300 MHz, for EUTs without a PE connection.