Tekbox

EMC near-field probe set with H- and E-field probes for pre-compliance measurement, supplied with TBWA2 20 dB broadband amplifier for increased dynamic range.

EMC near-field probe set with H- and E-probes for pre-compliance measurement, supplied with TBWA2 40 dB broadband amplifier for increased dynamic range.

Broadband amplifier for EMC measurement, intended for use between a near-field probe and a spectrum analyzer to increase the dynamic range during RF analysis.

EMC near-field probe set with H and E probes for pre-compliance measurement, designed for the localisation and analysis of radiated emissions in electronic designs.

Broadband amplifier for EMC measurement, intended for use between a near-field probe and a spectrum analyzer to increase the dynamic range during RF analysis.

Open 50 Ω TEM cell for pre-compliance measurement of radiated emissions up to 2 GHz, N-female, max 25 W, supplied with 50 Ω termination and DC block.

Operates from 2–70 V without an external power supply, with constant current and resistance modes, analogue control and an external voltage control input.

Open 50 Ω TEM cell for pre-compliance measurement of radiated emissions up to 2 GHz, N-female, max 25 W, supplied with 50 Ω termination and DC block.

Broadband RF driver amplifier for laboratory use, designed to amplify low-power RF sources or drive power amplifier stages across wide frequency bands.

Broadband RF driver amplifier for laboratory use, designed for amplifying low-power RF sources or driving power amplifier stages across wide frequency bands.

Modulated broadband RF driver amplifier for immunity testing, designed for CW, AM and PM signals as well as the operation of EMC probes and TEM cells.

Open 50 Ω TEM cell with 150 mm septum for pre-compliance measurement of radiated emissions up to 2 GHz, N-female, max 25 W, supplied with termination and DC block.

75 cm RF cable with RG58, 50 Ω. VSWR ≤1.2 at 3 GHz, attenuation ≤1.3 dB at 3 GHz and ≤2 dB at 6 GHz. DC–5.8 GHz.

75 cm RF cable with RG223, 50 Ω. VSWR ≤1.2 at 3 GHz, attenuation ≤1.1 dB at 3 GHz and ≤1.5 dB at 6 GHz. DC–6 GHz.

75 cm RF cable with RG58, 50 Ω. VSWR ≤1.2 at 3 GHz, attenuation ≤1.3 dB at 3 GHz and ≤2 dB at 6 GHz. DC–5.8 GHz.

75 cm RF cable with RG223, 50 Ω. VSWR ≤1.2 at 3 GHz, attenuation ≤1.1 dB at 3 GHz and ≤1.5 dB at 6 GHz. DC–6 GHz.

75 cm RF cable with RG58, 50 Ω. VSWR ≤1.3 at 3 GHz, attenuation ≤1.4 dB at 3 GHz. DC–5.8 GHz.

75 cm RF cable with RG223, 50 Ω. VSWR ≤1.3 at 3 GHz, attenuation ≤1.2 dB at 3 GHz. DC–6 GHz.

75 cm RF cable with RG316, 50 Ω. VSWR ≤1.2 at 3 GHz, attenuation ≤2.7 dB at 3 GHz. DC–6 GHz.

50 Ω open TEM cell for EMC pre-compliance up to 2 GHz, N-female, max 10 W RF input power and attenuation of higher-order modes.

PC software for EMC pre-compliance testing with pre-configured CISPR projects, correction files and support for automated reporting.

Input +10 to +20 dBm (max 25 dBm), drive frequency 1–350 MHz and comb spectrum 1 MHz–2.5 GHz, N-female input and N-male output.

RF attenuator set DC–3 GHz, 2 W with 3, 6, 10 and 20 dB attenuators, VSWR

Transient limiter with 10 dB attenuation, 9 kHz–600 MHz, +11 dBm threshold, max 5 W RF power and integrated 9 kHz high-pass filter, N-female to N-male.

RF attenuator set DC–3 GHz, 10 W with 3, 6, 10 and 20 dB attenuators, VSWR

For EMC pre-compliance measurements with conductive fabric, aluminium frame, AC/DC filter panel and coaxial feedthroughs, 120×60×60 cm.

High dynamic range amplifier for EMC measurement, designed as a low-noise preamplifier for spectrum analyzers, receivers and active loop antennas.

Coaxial adapter set with 44 x 50 Ω adapters, N-, SMA-, BNC-, SMB- and RCA-combinations in a storage box, for RF and HF measurement applications.

RF attenuator set DC–6 GHz, 2 W with 3, 6, 10, 15, 20 and 30 dB attenuators ±0.5/±0.8 dB and two 50 Ω terminations, VSWR

Modulated broadband RF driver amplifier for immunity testing, designed for CW, AM and PM signals as well as the operation of near-field probes and TEM cells.

Linear broadband RF power amplifier for test and measurement applications, designed for general laboratory use with stable gain over a wide frequency range.

For EMC pre-compliance measurements with conductive fabric, aluminium frame, AC/DC filter panel and coaxial feedthroughs, 86×49×45 cm.

For EMC pre-compliance measurements with conductive fabric, aluminium frame, DC filter panel and coaxial feedthroughs, 86×49×45 cm.

70 × 40 cm for storage and transport of ESD- and EMC-sensitive equipment, with attenuation of electrostatic and electromagnetic interference.

105 × 60 cm with two layers of conductive fabric and ~50 dB attenuation DC–2 GHz for EMC pre-compliance and interference reduction during measurements.

RF current monitoring probe with fixed shunt for EMC measurement, characterised for 30 kHz–1 GHz, flat frequency response and defined transfer impedance.

LISN with 5 µH inductance and 50 A capacity for DC-powered devices, 150 kHz–110 MHz measurement range, in accordance with CISPR 16-1-2 and related standards.

Biconical EMC measurement antenna for radiation testing and field strength generation, frequency range 30–300 MHz, dipole-like radiation pattern and 50 ohm impedance.

Double-ridge horn antenna for EMC pre-compliance measurements of radiated noise, 1–8 GHz, directional characteristics at high frequencies and 50 ohm impedance.

Modulated broadband power amplifier for RF immunity testing, designed for CW, AM and PM signals, as well as for operating near-field probes and TEM cells.

BNC accessory set with banana adaptors, terminal block adaptors and 50 Ω feed-through termination, SWR

3-phase power cable 16 A with CEE/IEC60309 3L+N+PE male to female, 3 m length for three-phase connection.

3-phase mains cable 16 A with CEE/IEC60309 3L+N+PE male to female, 5 m length for three-phase connection.

3-phase mains cable 16 A with CEE/IEC60309 3L+N+PE male to female, 10 m length for three-phase connection.

For IEC 61000-4-6 Annex D2. 150 kHz–230 MHz, 300 V AC / 600 V DC, 15 A, 150 Ω common-mode impedance and 9.5 dB voltage division.

For IEC 61000-4-6 Annex D2. 150 kHz–230 MHz, 300 V AC / 600 V DC, 36 A, 150 Ω common-mode impedance and 9.5 dB voltage attenuation.

For IEC 61000-4-6 Annex D2. 150 kHz–230 MHz, 300 V AC / 600 V DC, 36 A, 150 Ω common-mode impedance and 9.5 dB voltage attenuation.

RF surface current monitoring probe for EMC pre-compliance measurement of currents on surfaces such as PCB ground planes and conductors, characterised for 30 kHz–400 MHz.

RF surface current monitoring probe for EMC pre-compliance measurement of currents on surfaces such as PCB ground planes and conductors, characterised for 30 kHz–600 MHz.

2 kHz–70 MHz 3 dB bandwidth, 0 dBΩ transimpedance and N-female, characterised 10 Hz–100 MHz and max 12 A RF current.

3 kHz–100 MHz 3 dB bandwidth and 5 dBΩ transimpedance, characterised 10 Hz–100 MHz, N-female and max 12 A RF current.

400 kHz–600 MHz 3 dB bandwidth and 23 dBΩ transimpedance, characterised 10 Hz–600 MHz, N-female and max 12 A RF current.

Modulated RF power amplifier for immunity testing in accordance with IEC/EN 61000-4-6, designed for operation of CDNs and BCI probes with CW, AM and PM signals.

Passive loop antenna for EMC pre-compliance measurement of radiated emissions, 9 kHz–30 MHz in accordance with CISPR 16, for magnetic field measurements.

Slotted corrugated coaxial cable for 30 cm loop, 9 kHz–30 MHz, N-female and ¼” tripod thread, for magnetic and electric field measurement.

Modulated RF power amplifier for immunity testing in accordance with IEC/EN 61000-4-6, designed for operation of CDNs and BCI probes with CW, AM and PM signals.

Injection transformer for stability measurement of control loops, with galvanic isolation between signal source and DUT, intended for low-frequency RF tests.

Injection transformer for stability measurement of control loops, with galvanic isolation between signal source and DUT, intended for low-frequency measurements.

20 Hz–100 MHz 3 dB bandwidth and −20 dBΩ transimpedance, characterised 1 Hz–200 MHz, 25 mm aperture, N-female and up to 300 A RMS.

30 Hz–70 MHz 3 dB bandwidth and −26 dBΩ transimpedance, characterised 1 Hz–200 MHz, 5.5 mm aperture, SMA female and up to 40 A RMS.