Pico

18 GHz RF adapter, SMA female to N male, 50 Ω impedance for high-frequency connections.

3 GHz RF adapter, SMA female to BNC male, 50 Ω impedance for connection between RF and oscilloscope accessories.

Active high-impedance probe, 750 MHz bandwidth, 1 MΩ input impedance, 0.9 pF input capacitance and automatic probe detection with 50 Ω switching.

Active high-impedance probe, 1.3 GHz bandwidth, 1 MΩ input impedance, 0.9 pF input capacitance and automatic probe detection with 50 Ω switching.

4-channel data logger with 20-bit resolution, up to 15 measurements/s, multiple bipolar measurement ranges and USB interface for isolated data acquisition.

8-channel data logger with 24-bit resolution, up to 15 measurements/s, seven bipolar measurement ranges, digital I/O and USB interface for isolated data acquisition.

BNC to dual 4 mm banana plugs, 1.2 m cable for connection between BNC socket and measuring instrument.

4.5 m USB 2.0 cable with 20 AWG conductors for a stable power supply and reduced voltage drop when used with PicoScope oscilloscopes.

16-channel data logger for voltage measurement with 12-bit resolution, up to 1 MS/s sampling rate, DC-coupled inputs and USB connection.

3-channel current logger with 24-bit resolution, USB and Ethernet, and three included AC current clamps 0–200 A for single-phase and three-phase systems.

Terminal board with screw terminals for Pico ADC-20 and ADC-24 data loggers, simplifies connection of test leads without soldering.

Terminal board with screw terminals for PicoLog 1012 and 1216, with the option of resistors for offset and input matching without soldering.

Screw terminal adapter for PT-104, enables connection of discrete wires and sensors without soldering.

Hard carrying case with foam inserts for the PicoScope 3000D, 3400A/B, 4824 and 5000A/B series.

4 x P2036 300 MHz probes with magnetic PCB holders, 2.5 mm probe holders and A4 base plate for hands-free measurements up to 300 MHz.

4 x P2056 500 MHz probes, magnetic PCB holders, 2.5 mm probe holders and A4 base plate for hands-free measurements up to 500 MHz.

4-channel data logger for PT100/PT1000 with a measurement range of –200 to +800 °C, 24-bit resolution and USB and Ethernet connectivity.

Fibreglass-insulated Type K wire probe, 1 m long, for temperature measurement from −60 to +350 °C with mini-connector and fast response time.

For immersion, insertion and air measurement with a range of –30 to +350 °C, Class A accuracy and a 150 mm stainless steel probe with a 4-pin mini-DIN connector.

For immersion, insertion and air measurement with a range of –50 to +250 °C, 1/10 DIN accuracy ±0.03 °C, 150 mm stainless steel probe and 4-pin mini-DIN connector.

PT100 insertion probe for liquids, −75 to +250 °C measurement range, class A ±0.15 °C at 0 °C, 120 mm stainless steel probe and 4-pin mini-DIN.

Fast PT100 probe for air measurement, −75 to +250 °C measurement range, Class A ±0.15 °C at 0 °C, 120 mm stainless steel probe and 4-pin mini-DIN.

PT100 probe for air measurement, −60 to +500 °C measurement range, Class B ±0.3 °C at 0 °C, 150 mm stainless steel probe and 4-pin mini-DIN.

PT100 universal sensor, −75 to +260 °C measurement range, Class A ±0.15 °C at 0 °C, 120 mm stainless steel probe and 4-pin mini-DIN.

Fibreglass-insulated Type K wire probe, 2 m long, for temperature measurement from −60 to +350 °C with mini-plug and fast response time.

Fibreglass-insulated Type K wire probe, 5 m long, for temperature measurement from −60 to +350 °C with mini-plug and fast response time.

Active differential probe, DC–100 MHz bandwidth, 10:1/100:1 attenuation, ±700 V common-mode and up to 1000 V RMS CAT III.

Attenuator set with 3, 6, 10 and 20 dB, DC–1 GHz bandwidth, 50 Ω impedance, 1 W power and BNC male-to-female connection.

Feed-through terminator, DC–1 GHz bandwidth, 50 Ω impedance, 1 W power and BNC male-to-female connection.

Passive 10:1 low-impedance probe for 50 Ω input, 1.5 GHz bandwidth, 500 Ω input impedance, 2 pF capacitance and BNC connector.

AC current clamp, 0.1–200 A RMS range, 1 mV/A output via 4 mm banana plugs, ±2% accuracy and CAT II 600 V / CAT III 300 V.

Measuring range 200/2000 A AC/DC with BNC output, output sensitivity 10/1 mV/A, overload capacity 2200 A and accurate current measurement up to 2 kA.

18 GHz 50 Ω SMA male-to-female adapter, contact saver for frequent connection cycles and protection of sensitive RF inputs.

1.2 m USB 2.0 cable with 20-AWG conductors for a stable power supply and reduced voltage drop when used with PicoScope oscilloscopes.

D9 to single BNC adapter for differential and current probes, enables single-ended measurements with a ground-referenced probe.

USB Type-C to USB Standard-A (female) adapter, 0.14 m, for connecting PicoScope and PicoLog to a computer with a Type-C port.

D9 to dual BNC adapter for differential measurements with two single-ended probes or two BNC cables, compatible with PicoScope 4444.

40 A AC/DC current probe with D9 connector for the PicoScope 4444, DC–100 kHz bandwidth, 100 mV/A sensitivity and automatic identification via the scope’s connector.

AC/DC current probe with D9 connector for PicoScope 4444, 200 A/2000 A ranges, DC–20 kHz bandwidth and automatic probe identification.

3-phase AC current probe with Rogowski coil technology, measurement ranges 30/300/3000 A, 10 Hz–20 kHz bandwidth and BNC output for oscilloscopes and data loggers.

Single-phase AC current probe with Rogowski coil technology, measurement ranges 30/300/3000 A, 10 Hz–20 kHz bandwidth and 3 V AC output via BNC.

Passive 1:1/10:1 oscilloscope probe with 100 MHz bandwidth, BNC connector, redesigned probe tip for interchangeable tips and improved durability.

5-pack of fixed replacement tips for TA375 and TA386, screw-mounted replacement tips for oscilloscope probes.

Spring-loaded replacement tips for TA375 and TA386 oscilloscope probes, 5-pack of interchangeable tips for accurate measurement and extended probe life.

Passive 1:1/10:1 oscilloscope probe with 200 MHz bandwidth, BNC connector, redesigned probe tip for interchangeable tips and improved durability.

8-channel data logger for thermocouples with a measurement range of –270 to +1820 °C, 20-bit resolution, up to 10 measurements/s and USB connection.

1-channel terminal board for USB TC-08, screw terminals without soldering, supports ±5 V, ±500 mV, ±50 mV and 4–20 mA measurement.

Passive 1:1 differential probe for PicoScope 4444, 15 MHz bandwidth, ±50 V operating range, 4 mm banana plugs and D9 output.

Passive 25:1 differential probe for PicoScope 4444, 10 MHz bandwidth, up to ±1000 V measurement range, 1000 V CAT III and D9 connection.

Kit containing six RF and microwave probes (4–5 GHz) with selectable AC/DC heads, two low-loss cables and a complete set of accessories.

AC-coupled 20:1 probe with 4 GHz bandwidth for RF and microwave signals,

DC-coupled 20:1 probe with 4 GHz bandwidth for RF and microwave signals,

AC-coupled 10:1 probe with 4 GHz bandwidth for RF signals,

DC-coupled 10:1 probe with 4 GHz bandwidth for RF signals and pulses,

AC-coupled 5:1 probe with 5 GHz bandwidth,

DC-coupled 5:1 probe with 5 GHz bandwidth,

Kit containing six gigabit probes (6–9 GHz) for 12–18 Gb/s signals, two low-loss cables and a complete set of accessories including probe tips.

AC-coupled 20:1 probe with 6 GHz bandwidth for gigabit signals,

DC-coupled 20:1 probe with 6 GHz bandwidth for gigabit signals,

AC-coupled 10:1 probe with 7 GHz bandwidth,