Current Clamps

AC current clamp for non-intrusive measurement, 0.1–2000 A range, BNC output for DMM and oscilloscope, CAT III 600 V.

AC currents up to 9,000 A, high accuracy up to 3,000 A, wide frequency range, BNC connection and voltage output 1/10/100 mV/A.

AC/DC current clamp, 50 mA–100 A measurement range, DC–100 kHz bandwidth, 1 mV/mA and 10 mV/A output via insulated BNC and CAT III 600 V / CAT IV 300 V.

Measuring range 10 mA–100 A AC/DC with 1 MHz bandwidth, BNC output for oscilloscopes, 26 mm jaw opening, rechargeable battery and selectable filters 3 kHz/30 kHz.

Flexible AC current sensor 0.5 A–3 kA with Rogowski coil, 1 MHz bandwidth, 3 V output signal and 17 cm measuring loop with BNC connection.

Flexible AC current sensor 0.5 A–3 kA with Rogowski coil, 1 MHz bandwidth, 3 V output signal and 25 cm measuring loop with BNC connection.

Flexible AC current sensor 0.5 A–3 kA with Rogowski coil, 1 MHz bandwidth, 3 V output signal and 35 cm measuring loop with BNC connector.

AC current clamp, 1–500 A range (1200 A peak), 10 mV/A output via BNC, 5 Hz–10 kHz bandwidth and 1.5 m double-insulated cable.

AC current clamp for oscilloscopes with a measurement range up to 1000 A, 5 Hz–100 kHz bandwidth, passive filter for harmonics and BNC output for direct connection.

AC current clamp with 20 A/200 A measurement range, 10 mV/A and 100 mV/A output, BNC connection, frequency range 40 Hz–10 kHz and CAT III 600 V.

AC flexible current probe based on the Rogowski principle, 30 A/300 A/3000 A measurement range, 1/10/100 mV/A output, 610 mm flexible loop and CAT III 600 V.

AC Rogowski-type current probe, 30 A/300 A/3000 A measurement range, 1/10/100 mV/A output, 915 mm flexible loop and CAT III 600 V.

AC current clamp for oscilloscopes and DMM, up to 3000 A, 10 Hz–100 kHz bandwidth, BNC output via adapter for power distribution.

AC/DC current clamp with Hall-effect sensor, 30 mA–30 A range, DC–100 kHz bandwidth, BNC output and CAT III 300 V.

Hall-effect current probe for AC/DC, 30 A/300 A range, ±45 A/450 A DC, 10 mV/A–1 mV/A output, DC–20 kHz bandwidth and battery operation.

Two measurement ranges 40 A and 400 A AC with 10/1 mV/A output, BNC connection for oscilloscopes and power quality meters, CAT IV 600 V / CAT III 1000 V.

AC current clamp, 0.1 mA–120 A measurement range, mV output via 4 mm banana plug, Ø8 mm jaw width and CAT III 300 V.

Rogowski current probe with extended low-frequency bandwidth, 0.1 Hz–6 MHz, up to 300 kA peak current, ±6 V peak output and battery- or DC-powered integrator.

Rogowski current probe with compact coil, Hz–MHz bandwidth, 60 A–300 kA peak current, low droop and predictable phase response for 50/60 Hz and pulse measurements.

Rogowski current probe with 0.1 Hz–16 MHz bandwidth, 600 A–60 kA peak current, 40 kA/µs di/dt, 10 kV insulation and flexible clamp coil.

Rogowski current probe with 1.6 mm thin coil, Hz–30 MHz bandwidth, 30 A–30 kA peak current, up to 100 kA/µs di/dt and BNC output.

Shielded Rogowski current probe, 0.03 Hz–30 MHz bandwidth, 30 A–300 kA peak current, up to 120 kA/µs di/dt and 10 kV insulated clamp coil.

Shielded Rogowski current probe, up to 50 MHz bandwidth, 30 A–30 kA peak current, 12.5 ns rise time and BNC output for oscilloscope.

DC current probe for temporary measurements, 2–40 kA, single-shot with ±1% accuracy and analogue BNC output for DMM or oscilloscope.

Flexible AC current probe with two ranges, low phase shift at low frequencies and wide dynamic range, for power quality, leakage and earth current measurement.

Measuring range 200/2000 A AC/DC with BNC output, output sensitivity 10/1 mV/A, overload capacity 2200 A and accurate current measurement up to 2 kA.

3-phase AC current probe with Rogowski coil technology, measurement ranges 30/300/3000 A, 10 Hz–20 kHz bandwidth and BNC output for oscilloscopes and data loggers.

Single-phase AC current probe with Rogowski coil technology, measurement ranges 30/300/3000 A, 10 Hz–20 kHz bandwidth and 3 V AC output via BNC.

AC/DC current probe with Hall-effect sensor, DC–50 MHz bandwidth, 0–30 A linear range, 0.1 V/A output, 50 A peak current and 300 V CAT I.

AC/DC current probe, DC–10 MHz bandwidth, 150 A RMS, 300 A peak (500 A ≤30 µs), requires RP1000P power supply and is compatible with Rigol oscilloscopes.

AC/DC current probe, DC–2 MHz bandwidth, up to 500 A peak, 0.01 V/A output, ±1% accuracy and requires RP1000P power supply.